Investigation of impregnation speed depending on fillers during the manufacturing of parts by the vacuum infusion method
Аннотация
In the article examines the process of manufacturing three-layer carbon-fiber-reinforced plastic (CFRP) panels using the vacuum infusion method. A comparative analysis is conducted to assess the impact of various fillers on the manufacturability of the three-layer panel. Specifically, the study compares the impregnation speed of the part depending on the type of filler used.
For the research, the layers of carbon fabric and filler were laid simultaneously before sealing with vacuum film. A comparison was made between the manufacturability of using a non-woven reinforcing material (Soric) and polystyrene foam (Airex).
Литература
[1] Borodulin, A. S. INFLUENCE OF CHEMICAL NATURE OF FILLER ON VALUE OF RESIDUAL STRESSES / A. S. Borodulin, U. D. Kosimov, G. V. Malysheva // Klei. Germetiki. Tekhnologii. 2024. no 3. pp. 17-20.
[2] Borodulin, A. S. INFLUENCE OF CHEMICAL NATURE OF FILLER ON ADHESION STRENGTH VALUE / A. S. Borodulin, V. V. Mal'tsev, G. V. Malysheva // Klei. Germetiki. Tekhnologii. 2024. no 2. pp. 26-30.
[3] Tarasov D. D., Boiarchuk M. V., CHaplina E. S. INVESTIGATION OF EFFECT OF TECHNOLOGICAL SUPPORT ON MOLDING PROCESS QUALITY OF BASALTPLASTICS BY VACUUM INFUSION METHOD/ D. D. Tarasov, M. V. Boiarchuk, E. S. CHaplina // Klei. Germetiki. Tekhnologii. 2024. no 4. pp. 14-18.
[4] Konoplin A. Y., Baurova N. I. Hardness of the near-weld zone during contact spot welding of steels using an adhesive-weld technology // Russian Metallurgy (Metally). 2016. V. 2016. No 13. P. 1308-1311.
[5] Craddock, J.D. Method for direct measurement of on-axis carbon fiber thermal diffusivity using the laser flash technique / J.D. Craddock, J.J. Burgess, S.E. Edrington // Journal of Thermal Science and Engineering Applications. − 2017. − V. 9. − No. 1. − p. 014502.
[6] Das, T.K. Preparation, development, outcomes, and application versatility of carbon fiber-based polymer composites: a review / T.K. Das, P. Ghosh, N.C. Das // Advanced Composites and Hybrid Materials. − 2019. − No. 2. − pp. 214−233.
[7] Ding, J. Study on the curing reaction kinetics of a novel epoxy system / J. Ding, W. Peng, T. Luo // Rsc Advances. − 2017. − V. 7. − No. 12. − pp. 6981−6987. [8] Dmitriev, O.S. Thermo-chemical analysis of the cure process of thick polymer composite structures for industrial applications / O.S. Dmitriev, A.A. Zhyvenkova, A.O. Dmitriev // Advanced Materials & Technologies. − 2016. − No. 2. − pp. 53−60.
[2] Borodulin, A. S. INFLUENCE OF CHEMICAL NATURE OF FILLER ON ADHESION STRENGTH VALUE / A. S. Borodulin, V. V. Mal'tsev, G. V. Malysheva // Klei. Germetiki. Tekhnologii. 2024. no 2. pp. 26-30.
[3] Tarasov D. D., Boiarchuk M. V., CHaplina E. S. INVESTIGATION OF EFFECT OF TECHNOLOGICAL SUPPORT ON MOLDING PROCESS QUALITY OF BASALTPLASTICS BY VACUUM INFUSION METHOD/ D. D. Tarasov, M. V. Boiarchuk, E. S. CHaplina // Klei. Germetiki. Tekhnologii. 2024. no 4. pp. 14-18.
[4] Konoplin A. Y., Baurova N. I. Hardness of the near-weld zone during contact spot welding of steels using an adhesive-weld technology // Russian Metallurgy (Metally). 2016. V. 2016. No 13. P. 1308-1311.
[5] Craddock, J.D. Method for direct measurement of on-axis carbon fiber thermal diffusivity using the laser flash technique / J.D. Craddock, J.J. Burgess, S.E. Edrington // Journal of Thermal Science and Engineering Applications. − 2017. − V. 9. − No. 1. − p. 014502.
[6] Das, T.K. Preparation, development, outcomes, and application versatility of carbon fiber-based polymer composites: a review / T.K. Das, P. Ghosh, N.C. Das // Advanced Composites and Hybrid Materials. − 2019. − No. 2. − pp. 214−233.
[7] Ding, J. Study on the curing reaction kinetics of a novel epoxy system / J. Ding, W. Peng, T. Luo // Rsc Advances. − 2017. − V. 7. − No. 12. − pp. 6981−6987. [8] Dmitriev, O.S. Thermo-chemical analysis of the cure process of thick polymer composite structures for industrial applications / O.S. Dmitriev, A.A. Zhyvenkova, A.O. Dmitriev // Advanced Materials & Technologies. − 2016. − No. 2. − pp. 53−60.
Опубликован
2025-03-31
Как цитировать
Kosimov, U., Yudin , I., Eliseev , V., & Novikov , A. (2025). Investigation of impregnation speed depending on fillers during the manufacturing of parts by the vacuum infusion method. Международный научный журнал «Инженер», 3(1), 11-13. https://doi.org/10.56143/3030-3893-2025-1-11-13
Раздел
Аэрокосмическая инженерия
